Set-Backs and Mount Plates

55-0027 aux fixed bracket 350dpiFixed Outboard Motor Bracket 55-0027

SKU: 550027

  • Heavy duty aluminum bracket is designed to hold 2 and 4 stroke motors weighing up to 150lbs.
  • In addition, the model 27 has a 5” height adjustment to accommodate long shaft motors. 
  • 8 1/2” setback - weighs 13lbs.

55-0027 Spec Sheet

Owners Manual

 

55-0435 Fixed Auxiliary Motor Bracket 350dpiFixed Auxiliary Motor Bracket Model 435

SKU: 550435

This "fixed" Motor Bracket is designed for those rugged individuals who prefer to use their own strength to lift up their motors. It comes with the adjustable 13 in. setback feature and is made of 713 alloy aluminum. 

If you discover that you no longer want to test your strength, this bracket can be converted to a power tilt with the addition of our actuator, item number 99-55005. 

55-0435 Spec Sheet

Owners Manual
 

Static Motor Mount Plate Model 405
Static Motor Mount Plate Model 405

SKU: 550405 

If trolling motors are you thing – then our 405 static Plate is a must. It offers a sturdy and flat mounting area for your trolling motor clamps. Troll with confidence knowing that your trolling motor will stay where you put it!! This bracket makes mounting auxiliary and long shaft motors a snap. When direct to transom motor mounting is difficult, Panther’s Static Motor Mount Plate provides a flat secure mounting surface for clamp on or bolt on kicker motors two or four stroke up to 35 hp or 263 lbs. Made of solid cast aluminum with an 8 in. by 7 in. mounting area. The bracket can be used on most contoured boat transoms. The plate also works for mounting long shaft motors on short shaft transoms, because the plate set the motor 4 inches higher on the transom it’s perfect for jon boats and small fishing boats when a short shaft motor would otherwise be required. Convenient economical durable and easy to install, the Model 55-0405 is the answer to difficult transom installations.

55-0405 Spec Sheet

O
wners Manual





Set-back Plate Model 220 (2in)Set-back Plate Model 220 (2in)

SKU: 550220 

  • This cast aluminum spacer provides two inches of set-back for bolt-on motors, allowing performance seekers to fine tune their boats.
  • Dipped in a zinc rich primer then powder coated, this solid spacer installs directly to the transom, or adds additional set-back to an existing JackPlate.
  • A standard BIA hole pattern makes mounting a snap, but is drillable for non-standard patterns.

55-0220 Spec Sheet

55-0240 4 Set-back Plate 350dpiSet-back Plate Model 240 (4in)

SKU: 550240 

  • An innovative flared shape allows this four inch set-back bracket more transom contact area to reduce stress and improve the motor's stability.
  • The two piece, T-6 heat treated, 1/2" anodized aluminum bracket will work with even the most powerful main engines.
  • This is an inexpensive solution to lagging performance, while maintaining maximum durability.
  • The pre-drilled hole patterns allow for an extensive range of motor installations. 
  • Bracket mounting dimensions: 3" motor side x 13" & 4.75" transom side x 13"

BIA bolt patterns apply. 

55-0240 Spec Sheet

 

Spacer Kit for Model 35 Lift and 435 Bracket -3 inchSpacer Kit for Model 35 Lift and 435 Bracket

SKU: 559035 

This two piece, cast aluminum spacer provides an extra three inches of setback for the Model 35. Impossible installations are a thing of the past, and it allows your kicker motor to be tilted up without hitting your transom. The spacer will extend the Model 35 to 16" of setback. Chromate dipped, powder paint coated for maintenance free durability.

55-9035 Spec Sheet


 

Reversible Wedge Plate Model 420
Reversible Wedge Plate Model 420

  • SKU: 550420 
  • The Reversible Wedge Plate provides five degrees of trim or tuck.
  • Its one piece, cast aluminum design provides a stable platform for the largest of today's outboards.
  • Heavy boats will benefit from the additional performance of five degrees of bow lift.
  • Bow light boats will benefit by reversing the wedge, keeping the boat adhered to the water and providing a much improved hole shot.
  • The chromate dipped, powder painted wedge offers hole patterns to suit a wide variety of mounting applications. 

BIA bolt patterns apply.




 

Motor Mount Bolt BarMotor Mount Bolt Bar

SKU: 559100 

  • The Motor Mount Bolt Bar will supply the added support for your transom, when mounting your main or auxiliary motors.
  • Made from heavy duty cast aluminum and powder coated for years of like new looking support.

55-9100 Spec Sheet